4PCs Replacement Analog Joystick for PlayStation 4 Wireless Controller - ElecGear Repair P

Product Description

4PCs of brand-new analog joystick for Sony PS4, PS4 Slim, PS4 Pro wireless controller. The replacement repair parts was made by ALPS which is the same maker as the one in the official controller. OEM quality to ensure games accuracy and prolong lifespan

It's a hard time to take off the problem sensor module with as many as 14 prongs. We figured out ways to make it possible based on situations below:

● A heat gun to replace the whole assembly
This is the most suggested for an experienced soldering expert
● Partially replace the 3Pin potentiometer sensor alone with an iron
According to some estimates, 80% chances of problem are caused by the motion sensor. In another words, the joystick rocker and the tactile switch are good. In this case, you can try to swap the 3Pin sensor alone. (We're listing the 3Pin sensors alone.)
● Replace the white disc alone even without soldering
In some cases, you can just replace the little wheel in the 3Pin potentiometer sensor to solve some specific problems like: Dead spot, blind spot, dead zone, creeping, not as responsive as it should be
● Experts with a normal iron to replace the whole unit
For a soldering expert with NO professional desoldering wick braid, solder sucker pump or hot air rework station at hand. We suggest to crush the problem thumstick into small enough pieces with a pair of pliers. It will be much more easier than de-soldering the entire 14Pin unit
● by professional technicians in a cellphone repair shop
Suggested for someone with no handy tools

Scan the barcode included in the package to view the instruction and demonstration offered by ElecGear webpage. We are talking about the stick problems and always trying hard to find a way to make it easier

What's in Package:
4* Analog joystick (For official PlayStation DualShock 4 ONLY! )
1* PH000 screwdriver

Features

• [EL6 ALPS 2.1K for PS5 and PS4] – 4x replacement analog joystick work with PlayStation 5 DualSense and some PS4 DualShock 4 wireless controllers. The thumbstick module was made by ALPS. This RKJXV stick controller series comes with 2.1KΩ trimmer potentiometers
• [Compatibility] – We’re listing two ALPS models for PS4 and PS5. The difference is the resistance value of the potentiometers. You can distinguish them from the color of the side plastic. EL1 is 10KΩ in gray, while EL6 is 2.1KΩ in black or green. PS5 controller uses two kinds of joysticks from two different manufacturers. EL6 was made by ALPS, while EL7 was from Favor Union (FU). They’re interchangeable with each other
• [Additional Resistor] – Complicated moving mechanism and daily wear and tear finally caused drifting. Even new sensors cannot be 100% balanced. Calibrating in controller settings might not work. We packed 10x correction resistors to solve the potential problem in hardware level. Solder one or two paralleled tiny resistors onto the potentiometer at the opposite direction against drifting. It will help correct 3 to 5 degrees drifting
• [When to replace] – The analog joystick needs to be replaced when your controller has the problem of drifting, creeping, stuttering, a blind spot, a dead spot, a dead zone, no reaction when clicking, or it wouldn't center after years of wear and tear. The OEM genuine repair parts ensure accuracy and prolong lifespan
• [Reminder of DIY] – With as many as 14 prongs, de-soldering and soldering the whole module takes serious skills. We suggest replacing the potentiometers first to solve most of the joystick problems. To desolder the entire joystick module off PCB by a normal soldering iron, please take a look at the desoldering kit at product ID: B0BK7169M8

Customers Who Bought This Item Also Bought

*If this is not the "4PCs Replacement Analog Joystick for PlayStation 4 Wireless Controller - ElecGear Repair Parts 3D Th" product you were looking for, you can check the other results by clicking this link.  Details were last updated on Apr 26, 2024 11:00 +08.